In this article
Quick answer
Gypsum board is the default for dry interior partitions in Dubai, while cement board belongs in wet areas, external soffits and tile-heavy walls. For Dubai fit-outs, gypsum board is the right partition material for most dry interior spaces such as offices, bedrooms, living rooms and retail back-of-house, because it is light, fast, cheap and easy to finish smoothly.
Last updated:
For Dubai fit-outs, gypsum board is the right partition material for most dry interior spaces such as offices, bedrooms, living rooms and retail back-of-house, because it is light, fast, cheap and easy to finish smoothly. Cement board is the right choice where walls get wet or carry heavy tiles: showers, wet kitchens, pool rooms, external soffits and semi-outdoor areas. Many good projects use both, with moisture-resistant gypsum in bathrooms that do not get direct water and cement board inside shower zones.
This guide compares gypsum board vs cement board partitions the way a Dubai fit-out contractor thinks about them: performance, approvals, acoustics, fixing loads, speed and realistic cost.
What gypsum board and cement board are
Gypsum board (drywall)
Gypsum board is a core of gypsum plaster faced with paper or glass-fiber mat. In the UAE it is usually installed on galvanised steel studs and tracks at 600 mm or 400 mm centers, with one or two layers of board on each side and mineral wool insulation in the cavity. Common types include:
- Standard board for dry walls and ceilings.
- Moisture-resistant (MR) board, often green-faced, for bathrooms, pantries and humid areas away from direct water.
- Fire-rated board, often pink or red-faced, used in systems tested to achieve a fire rating.
- Impact-resistant and acoustic boards for corridors, schools, hospitals and hotel rooms.
Cement board
Cement board is a sheet of cement reinforced with glass-fiber mesh or cellulose fibers. It does not soften or rot when wet, which makes it a stable backing for tiles and stone. It is heavier and harder to cut than gypsum, and it is usually installed on heavier-gauge studs with corrosion-resistant screws. Fiber-cement boards are also used outdoors for cladding and soffits.
Gypsum board vs cement board: side-by-side comparison
| Factor | Gypsum board | Cement board |
|---|---|---|
| Water resistance | Standard: poor; MR: tolerates humidity, not direct water | Unaffected by water, but not waterproof on its own |
| Weight | Light, easy to handle | Heavy, needs stronger framing |
| Finish | Very smooth paint finish after jointing | Usually tiled, stone-clad or skim-coated |
| Tile load | Fine for light tiles; check limits for large format | Better for heavy tiles and stone |
| Fire performance | Excellent in tested fire-rated systems | Non-combustible; ratings depend on system |
| Acoustics | Very good with double layers and insulation | Good mass, but less common in acoustic systems |
| Speed | Fast to install and finish | Slower: cutting, fixing and handling |
| Indicative cost | Lower | Higher |
Where each material belongs in a Dubai project
Use gypsum board for
- Office partitions, meeting rooms and cabins in Business Bay, DIFC, JLT and Dubai Silicon Oasis.
- Bedroom and living-room partitions in apartments and villas.
- Feature walls, TV walls, bulkheads and false ceilings with cove lighting.
- Fire-rated corridors and shafts, using the board manufacturer's tested system.
- Retail back-of-house and store rooms.
Use cement board for
- Shower walls and walk-in wet rooms behind tiles, always with a waterproofing membrane.
- Steam rooms, pool plant rooms and laundries with frequent splashing.
- Commercial kitchens and dirty kitchens where walls are washed down.
- Covered terraces, external soffits, outdoor kitchens and majlis tents with semi-outdoor exposure.
- Walls carrying heavy natural stone or very large porcelain slabs.
Gray areas
Guest bathrooms without showers, powder rooms and pantries are often built in MR gypsum with tiles to splash height. That is acceptable when ventilation is good and a waterproofing coat is applied behind any tiled zone near taps. For shower enclosures, most UAE contractors now prefer cement board or block walls with a full waterproofing system.
Moisture, humidity and AC condensation
In UAE buildings, partition damage often comes not from showers but from hidden water: a leaking AC drain pan above the ceiling, condensation on chilled-water pipes, or a dripping fan-coil unit in the corridor. Standard gypsum board wicks water and loses strength. MR board resists humidity but still fails under a constant leak. Cement board survives wetting, though the finishes on it may not.
Practical rules that save repair bills:
- Keep the bottom track of gypsum partitions off wet floors, or sit it on a small concrete or cement-board curb in pantries and bathrooms.
- Use MR board in any room with water points, even if no shower is planned.
- Insist on drip trays and accessible drain lines for every ceiling AC unit.
- Waterproof the backing behind every shower and wet zone; cement board is not a membrane.
Fire ratings and approvals
Partitions in commercial fit-outs are reviewed as part of the approval drawings. Depending on the location, that may involve Dubai Municipality, Dubai Civil Defence (DCD), Trakhees for Ports, Customs and Free Zone areas, DDA for its communities, or Nakheel, Emaar and other master developers for their buildings. Fire-rated partitions must follow a tested system from the board manufacturer: board type, number of layers, stud size, insulation and sealants all count. Swapping one board for another without checking the system can invalidate the rating.
For residential renovations, adding or moving partitions in an apartment or villa usually needs a no-objection certificate from the developer or community and sometimes a building permit. Check the current requirements and fees with the relevant authority before work starts.
Acoustic performance
Gypsum partitions win on acoustics per kilogram because the system can be tuned. A single-stud wall with one layer each side and no insulation is fine between a store room and a corridor, but it will not keep conversations private. For meeting rooms, bedrooms and hotel rooms, typical upgrades include:
- Two layers of board on each side with staggered joints.
- Mineral wool in the cavity.
- Acoustic sealant at the head, base and around sockets.
- Running the partition up to the slab, not just to the false ceiling.
- Acoustic or double-stud systems for cinemas, music rooms and executive offices.
Cement board adds mass, which helps with low-frequency noise, but it is rarely the most cost-effective way to achieve a sound rating indoors.
Fixing TVs, cabinets and heavy items
One of the most common client questions is whether a gypsum wall can hold a TV or kitchen cabinets. It can, if planned. Contractors add plywood or steel backing between the studs before boarding, then fix into that backing. Mark these zones on the drawings: TV walls, wall-hung WCs, basins, upper cabinets, grab bars in elderly-friendly bathrooms and heavy mirrors. Retrofitting backing later means cutting the wall open.
Cement board holds screws better than gypsum, but heavy items should still be fixed into framing or backing, not into the board alone.
Indicative 2026 costs in Dubai
The ranges below are indicative 2026 supply-and-install ranges for Dubai, per square meter of wall area, before 5% VAT. Final prices depend on height, insulation, number of layers, finishes, site access, working hours and approval requirements.
| Partition type | Indicative AED per m² |
|---|---|
| Single-layer gypsum, standard, on metal studs (painted finish extra) | 90–150 |
| Double-layer gypsum with insulation | 140–240 |
| MR gypsum for bathrooms and pantries | 110–190 |
| Fire-rated gypsum system | 160–300 |
| Cement board on metal studs (tiling and waterproofing extra) | 170–300 |
| Jointing, skim and paint on gypsum | 25–60 |
Compare quotations line by line. A cheap partition rate often excludes insulation, backing, door openings, access panels or the jointing and painting that make the wall look finished.
Installation tips that separate good contractors from average ones
- Set out accurately. Partitions should align with ceiling grids, window mullions and floor finishes.
- Use the right studs. Tall walls in villas and showrooms need deeper or heavier-gauge studs to avoid flexing.
- Plan services first. Electrical boxes, data cables, AC drains and plumbing should go in before the second side is boarded.
- Treat joints properly. Gypsum joints need tape and compound in several coats; cement board joints need alkali-resistant mesh tape.
- Protect corners. Metal or PVC corner beads keep edges sharp in busy corridors.
- Respect curing and drying. Painting over damp compound in humid months can cause flashing and cracks.
What about blockwork?
Some clients ask whether they should skip boards altogether and build in concrete block. Blockwork is common in villas for structural and external walls and for bathrooms in new construction. For interior fit-outs, especially in towers, it has clear downsides: it is heavy, which may exceed floor loading limits or building rules; it is wet work that brings dust and curing time; and it is slow to modify later. Board partitions on studs are lighter, faster, quieter to install and easier to remove when a tenant changes. In villas, a mixed approach is common: block for wet rooms and external extensions, gypsum for internal layout changes such as splitting a large bedroom or creating a home office.
Questions to ask your fit-out contractor
- Which board type and thickness are you using for each wall, and is it shown on the drawings?
- What stud size, gauge and spacing are you using for this wall height?
- Is insulation included, and what density?
- Where are you installing backing for TVs, cabinets and sanitaryware?
- Which waterproofing system goes behind the cement board in the shower, and up to what height?
- Are jointing, skim coat, primer and paint included in the rate?
- Who handles the building permit, NOC and inspections?
Clear answers to these questions usually reveal whether two quotations are really comparable, and they protect you from finding out about missing items after the walls are closed.
Common mistakes
- Using standard gypsum in a shower area and relying on tiles to keep water out.
- Treating cement board as waterproof and skipping the membrane.
- Stopping acoustic partitions at the false ceiling.
- Forgetting backing for TVs, wall-hung sanitaryware and cabinets.
- Mixing boards from different fire-rated systems.
- Starting partition work in a tower before the building permit is issued.
Key takeaways
- Gypsum board is the best choice for dry interior partitions: fast, smooth, affordable and excellent acoustically.
- Cement board belongs in showers, wet rooms, outdoor soffits and walls with heavy tiles or stone.
- MR gypsum is fine for humid rooms but not for direct water.
- Fire-rated walls must follow a complete tested system and the approved drawings.
- Plan backing for heavy fixtures before boarding.
Planning an office fit-out or a villa layout change? FIXORA Decor designs and builds gypsum and cement-board partitions in Dubai, handles approval drawings and coordinates MEP inside the walls. Message us on WhatsApp +971501962136 or request a quote with your layout.
The information in this article is general guidance, not advice for your specific project. See our Terms.
Frequently asked questions
Sources
Was this article helpful?
Get new articles by email
Practical tips now and then. Confirm by email, unsubscribe any time.



