On this page
Quick answer
Electrical and plumbing services in Dubai: lighting and smart switches, DB panels and earthing, leak detection, water heaters, pumps and bathroom and kitchen sanitary fit-out. Electrical and plumbing services in Dubai cover the hidden systems that keep a home or office safe and working: wiring, distribution boards, lighting, sockets, water supply, drainage, water heaters and pumps.
Key facts
- Our electrical and plumbing visits start from AED 150 per visit.
- The ranges below are typical indicative 2026 figures for Dubai, exclusive of 5% VAT.
Last updated:
Electrical and plumbing services in Dubai cover the hidden systems that keep a home or office safe and working: wiring, distribution boards, lighting, sockets, water supply, drainage, water heaters and pumps. FIXORA Decor provides DEWA-compliant electricians and plumbers for repairs, upgrades and fit-out work, from a tripping breaker or dripping tap to rewiring, DB upgrades, leak detection and complete bathroom and kitchen sanitary installations.
Electrical and plumbing faults tend to get worse quietly. A loose connection heats up inside a board, a slow leak behind tiles soaks into a neighbor's ceiling, a water heater's safety valve stops working. In UAE conditions, where AC loads are heavy, roof tanks get very hot and buildings are densely occupied, catching problems early saves money and avoids disputes. This guide explains what we do, how a visit works and what to expect on cost.
What the service covers
Electrical
- Fault finding: tripping breakers and RCDs, dead sockets, flickering lights, burning smells and overheating points.
- Lighting: downlights, pendants, LED strips, outdoor lights, dimmers and lighting circuits for renovations.
- Smart switches and controls: replacing standard switches with smart or touch switches, scene control and timers.
- DB panels and earthing: board inspection, breaker and RCD replacement, labeling, board upgrades and earthing checks.
- New points and circuits: additional sockets, dedicated circuits for ovens, induction hobs, water heaters and AC units.
- Rewiring: partial or full rewiring during renovation of older villas and apartments.
Plumbing
- Leak detection and repair: locating hidden leaks in walls, floors and ceilings, repairing pipes, valves and fittings and making good.
- Water heaters: repair, flushing, anode and safety valve replacement and new heater installation.
- Pumps: booster and transfer pump installation and repair for villas with low water pressure.
- Drainage: blocked sinks, floor drains and WCs, and drain smell investigation.
- Sanitary fit-out: installing basins, WCs, concealed cisterns, showers, mixers, kitchen sinks and appliances as part of bathroom and kitchen renovation.
When you need an electrician or plumber
- Breakers or the RCD trip repeatedly, particularly when the AC or kettle switches on.
- Sockets or switches feel warm, look scorched or crackle.
- Lights flicker across several rooms rather than at one fitting.
- Your water bill rises without a change in use, or the water meter turns with all taps closed.
- Damp patches, bubbling paint or loose tiles appear near bathrooms or kitchens.
- There is a drain smell in a bathroom, or water drains slowly.
- Hot water runs out quickly, is rusty or the heater makes rumbling noises.
Signs of electrical overheating, burning smells or water near electrics need urgent attention: switch off the relevant breaker if it is safe to do so and call a professional. Our guide to electrical safety checks for villas lists what an inspection should include.
How the process works with FIXORA Decor
- Describe the problem. Send a short description and photos or a video by WhatsApp: the board, the leak, the fitting. This helps the technician bring the right parts.
- Booking and access. We agree a slot and confirm any building permit, contractor access request or service lift booking needed.
- Diagnosis. The technician isolates the fault using testing equipment, explains the cause and the options, and confirms the cost before carrying out chargeable work.
- Safe isolation and repair. Power or water is isolated, the repair is made using suitable materials, and affected areas are protected from dust and water.
- Testing. Circuits are tested after electrical work; pipework is checked under pressure and fixtures run to confirm there are no leaks.
- Making good and handover. Small openings are closed. Where tiling or painting is needed, we agree it as part of the job or arrange it through our maintenance team.
Options and materials compared
| Decision | Option A | Option B | What usually works in the UAE |
|---|---|---|---|
| Water heater | Storage heater (50–200 liters) | Instant electric heater | Storage for family bathrooms; instant units for a single basin or a small kitchen |
| Leak repair | Open the wall at the leak and repair | Reroute new pipework | Spot repair where pipes are sound; reroute where pipes are old or have repeated failures |
| Circuit protection | Standard MCBs with a shared RCD | RCBOs per circuit | RCBOs limit how much of the home goes off when one circuit trips |
| Switches | Standard switches | Smart or touch switches | Smart switches in living areas; check neutral availability at the switch box |
| Lighting | Warm white (around 2700–3000 K) | Neutral white (around 4000 K) | Warm for living and bedrooms, neutral for kitchens, offices and work areas |
For lighting choices, see our LED lighting guide.

UAE climate considerations
Heat and electrical load
Summer AC demand pushes circuits and boards harder than at any other time of year. Loose terminals and undersized cables show up as tripping or heat marks in June and July. A board check before summer is a sensible precaution, especially in older villas where loads have grown with extra AC units, kitchens and outdoor lighting.
Hot roof tanks and water heaters
In villas with roof tanks, cold-tap water can run very warm in summer. Many owners lower the water heater setting or switch heaters off during the hottest months, which saves electricity. Hard water and sediment shorten heater life, so flushing and anode checks matter. Read our guide to water heater maintenance and replacement.
Outdoor electrics, dust and rain
Outdoor sockets and lights on villas and terraces face sun, dust and occasional heavy rain. Use weatherproof fittings with a suitable IP rating and protect outdoor circuits with an RCD.
Humidity and drains
Dry floor drain traps let sewer smells into bathrooms that are rarely used, a common issue in guest bathrooms and homes left empty over summer. Our guide to bathroom drain smells explains the fixes.
Approvals and building rules
Small repairs and like-for-like replacements generally do not need authority approval, though buildings usually require notice or a permit for contractors. Larger electrical changes are different: increasing the connected load, replacing a main incoming cable or adding significant new circuits may need DEWA approval in Dubai, or the equivalent utility elsewhere, and work by an appropriately approved contractor. Renovations with substantial plumbing or electrical changes may also need an NOC from building management or the master developer. Our article on DEWA load increases and electrical approvals explains the general process; always check current requirements and fees with the authority. In apartments, plumbing work that affects shared risers or stacks must be coordinated with building management.
Indicative costs
Our electrical and plumbing visits start from AED 150 per visit. The ranges below are typical indicative 2026 figures for Dubai, exclusive of 5% VAT. They depend on scope, access and finishes, and are confirmed after inspection or a site survey.
| Work | Typical indicative range (AED) |
|---|---|
| Replace flexible hose or angle valve | 120–250 per fixture |
| Concealed cistern repair | 250–600 |
| Professional leak detection visit | 350–1,500 depending on equipment and property size |
| Concealed pipe repair, open and close wall | 800–2,500, tile matching extra |
| New 50 liter water heater, supplied and installed | 600–1,100 |
| New 80 liter water heater, supplied and installed | 800–1,400 |
| Annual board and RCD check | 350–800 |
| Replace an RCD or RCBO | 250–600 each |
| Replace distribution board | 3,500–9,000 |
| Partial rewiring, per room | 2,500–6,000 plus making good |
Cost factors include access (high ceilings, concealed pipework, tight cupboards), the finish that has to be opened and reinstated, parts availability and any authority fees for approved changes. For leaks, read plumbing leaks in Dubai apartments: what to do.
Electrical and plumbing as part of a renovation
During kitchen and bathroom renovation, first-fix electrical and plumbing work happens before walls are closed and tiled, so mistakes are expensive to fix later. Agree socket heights, appliance positions, mixer types and drain positions with the designer before work starts, and photograph pipe and cable routes before they are covered. Pressure-test water pipes and test circuits before tiling. Our turnkey fit-out service coordinates these trades within one program.
Simple checks you can do between visits
Many problems can be spotted early without tools. These checks take a few minutes and do not involve opening any electrical equipment:
- Press the test button on each RCD every few months; it should trip immediately. If it does not, call an electrician.
- Look at the board for scorch marks, warm covers or a burning smell, and keep the area around it clear and dry.
- Check the flexible hoses under sinks and behind WCs for bulging, rust or drips, as these hoses are a frequent cause of apartment floods.
- Run water in unused bathrooms and pour water into floor drains every week or two to keep traps sealed.
- Read the water meter at night with all taps closed and again in the morning; any movement suggests a leak.
- Before traveling over summer, close the main water valve and switch off the water heater if no one will use it.
Write down what you notice and share it at the next visit; patterns such as tripping only at certain times help the technician find the cause faster.

How to prepare
- Know where your main water valve and distribution board are, and label circuits if they are not labeled.
- Clear access to the board, the water heater, under-sink cupboards and any ceiling access panels.
- Take photos or a short video of the fault, including when it happens.
- Arrange building permits and access, and inform neighbors if water or power to shared areas may be affected.
- For leaks, note whether the damp area grows when a particular fixture is used.
- Keep warranty paperwork for appliances and heaters to hand.
Related products
Common items we install include the 80 liter electric water heater, the smart water leak sensor kit with auto shut-off valve, the smart glass touch switch set and the 0.5 HP booster pump.
Key takeaways
- Repeated tripping, warm sockets and burning smells need prompt professional attention.
- Find and fix the source of a leak before repairing ceilings and finishes.
- Check boards before summer, when AC loads peak.
- Load increases and major electrical changes may need DEWA approval; check current requirements.
- Indicative prices depend on access and finishes and are confirmed after inspection.
Book an electrician or plumber
Every job is carried out by vetted, trained professionals with transparent pricing and a workmanship guarantee. Send photos and a short description to FIXORA Decor on WhatsApp +971501962136, call +971 50 196 2136, or request a quote for larger upgrades and renovation work.
What's included
- Lighting & smart switches
- DB panel & earthing
- Leak detection & repair
- Water heater & pump installation
- Bathroom & kitchen sanitary fit-out
Gallery
Frequently asked questions
Common causes are an overloaded circuit, a faulty appliance or AC unit, moisture in an outdoor fitting, or a loose connection in the board. An electrician can test each circuit to find the cause.
Close all taps and watch the water meter; if it still moves, there is likely a leak. Damp patches, bubbling paint, loose tiles and musty smells near wet areas are other signs.
Small repairs and like-for-like replacements usually do not, but load increases and significant changes to the supply or circuits may. Check current requirements with DEWA and your building before starting.
An annual check of the safety valve, anode and sediment is sensible in the UAE because of hard water and sediment. Replace the heater if it leaks from the tank or the relief valve keeps discharging.
Our visits start from AED 150. Larger jobs such as leak detection, board replacement or rewiring are quoted after inspection, with indicative ranges shown above, excluding VAT.



