
Specialty coffee kiosk fit-out in an Al Reem Island mall, Abu Dhabi
An illustrative mall kiosk fit-out for a specialty coffee concept on Al Reem Island, Abu Dhabi: a 14 m² island unit with a compact bar, drainage and power run under a live mall floor, built entirely at night and handed over in five weeks.
Quick answer
An illustrative mall kiosk fit-out for a speciality coffee concept on Al Reem Island, Abu Dhabi: a 14 m² island unit with a compact bar, drainage and power run under a live mall floor, built entirely at night and handed over in five weeks.
Key facts
- Week 1: hoarding, core drilling and services from the level below, done between midnight and early morning with the car park bay below closed off.
Last updated:
This mall kiosk fit-out in Abu Dhabi shows how a 14 m² specialty coffee island can be designed, approved and built inside a trading mall without closing the walkway. FIXORA Decor delivered the kiosk on Al Reem Island in five weeks, working only at night, with a full espresso bar, under-counter refrigeration, a hand-wash sink and a menu display that met the landlord's height and sightline rules. This case study is an illustrative example based on typical projects of this type; the client is not named.
The brief: a mall kiosk fit-out that works like a full café
The operator already ran a small roastery and wanted a first retail point in a busy community mall on Al Reem Island. The landlord offered an island position on the ground floor between two anchor stores, with clear views from both escalators. The brief was simple to say and hard to deliver: serve a full espresso and filter menu at peak times with two baristas, keep the kiosk below the mall's maximum height so it did not block shopfronts behind it, and open in time for the cooler months when footfall in UAE malls is at its highest.
The operator also wanted the kiosk to feel like a piece of furniture rather than a box. That meant rounded corners, warm timber, a stone counter that customers could lean on, and no visible cables, bins or packaging. Storage had to be hidden but reachable without the baristas stepping out of the kiosk footprint, because mall rules do not allow stock or boxes in the common area during trading hours.
Challenges
- Services under a live floor. An island kiosk has no wall to hide pipes and cables in. Water, drainage and power had to come up through the mall slab from the car park level below, which meant core drilling, a structural check and coordination with the mall's facility management team.
- Night-only working. The mall allowed works only after closing, roughly from midnight to early morning, and every evening the area had to be hoarded, cleaned and safe for cleaners and security patrols.
- Heat and equipment load. An espresso machine, grinder, under-counter fridges and a small dishwasher create a lot of heat in a very small space. Without planning, the baristas would be working in an oven and the equipment would trip breakers in the afternoon.
- Food handling rules. Even a coffee kiosk serving pastries needs hand-wash provision, cleanable surfaces and correct separation of clean and dirty areas, so the layout had to satisfy food-safety inspectors as well as the landlord.
Approvals (in general terms)
In Abu Dhabi, a kiosk inside a mall normally goes through several layers of approval. The landlord's fit-out team reviews the design against its tenant criteria first: height, branding, materials, lighting levels and how the kiosk is serviced. Once the landlord is satisfied, drawings go through the relevant municipal and Civil Defence channels for the fit-out permit, fire and life-safety items and electrical load, and the food-safety side is handled with the relevant food control authority before trading starts. FIXORA Decor prepared the drawing set, equipment schedule and material samples, and the operator's trade license details were attached where required. Fees and timelines vary by mall and authority, so we always recommend checking current requirements with the landlord and authority at the start rather than relying on a previous project.
Design approach
We designed the kiosk as an oval with one straight service side facing the back-of-house corridor. The customer side wraps around three quarters of the unit, giving queue space from two directions so people do not block the escalator landing. The espresso machine sits on the long front counter, facing customers, because the operator wanted the coffee-making to be part of the show. Grinders and the filter station sit on a raised back counter so baristas can turn between them without walking.
Below counter level, the kiosk is effectively a set of drawers and cupboards. We specified full-extension runners rated for heavy loads, push-to-open doors with no handles on the customer side, and a lockable stock cupboard for milk, cups and lids that can be refilled at night from the corridor. The menu is a slim illuminated panel on a single steel post, kept well below the landlord's maximum height so the shopfronts behind remain visible.
To handle heat, we placed the fridges with front ventilation grilles and a dedicated air path, and asked the mall to adjust the nearest supply diffuser to throw air across the bar. The equipment was split across separate circuits so a fridge compressor and the espresso boiler could not overload one breaker during the afternoon rush.
Scope of work
- Survey of the mall slab and services below; core drilling for water, drainage and power with fire-stopping on completion
- Supply and installation of a sub-distribution board with separate circuits for each major appliance and residual-current protection
- Water supply with filtration for the espresso machine, a hand-wash sink, a bar sink and a pumped drainage connection where gravity fall was not possible
- Custom joinery base in moisture-resistant board on a steel frame, with timber veneer and a high-pressure laminate interior
- Solid surface and quartz countertops with integrated sinks and rounded edges
- Menu panel, under-counter LED lighting and a pendant cluster within the landlord's allowed zone
- Hoarding, protection of the mall floor and nightly cleaning
- Testing, commissioning and handover documents
Materials
| Element | Material | Why we chose it |
|---|---|---|
| Kiosk frame | Galvanised steel box section | Rigid, does not rot if a leak happens, easy to anchor to the slab |
| Base panels | Moisture-resistant MDF with oak veneer and lacquer | Warm look, stable in air-conditioned malls, repairable |
| Front counter | Quartz, 20 mm with rounded edge | Hard-wearing, easy to clean, comfortable to lean on |
| Back counter and sinks | Solid surface with integrated bowls | No seams for food-safety inspections, invisible joints |
| Kiosk interior | High-pressure laminate, white | Cleanable, resists coffee stains and heat |
| Plinth and kick | Brushed stainless steel | Survives mall floor scrubbers and trolleys |
| Lighting | Warm white LED strip and pendants, 2700–3000K | Makes coffee and pastries look appetising, low heat |
Program: five weeks of night works
The joinery and steel frame were fabricated in our workshop while approvals were in progress, which saved roughly three weeks compared with building on site. On site, the program looked like this:
- Week 1: hoarding, core drilling and services from the level below, done between midnight and early morning with the car park bay below closed off.
- Week 2: steel frame installed and anchored, first-fix electrical and plumbing, pressure testing of water lines.
- Week 3: joinery panels and countertops installed in modules that fitted through the mall service corridor and lifts.
- Week 4: equipment set in place, menu panel and lighting, final electrical connections.
- Week 5: testing and commissioning, snagging, landlord and authority inspections, deep clean and barista training on site.
Each morning before the mall opened, the area was hoarded, the floor swept and any dust removed. Noisy drilling was finished early in the shift so that cleaning crews could work later without disturbance.
Handover
At handover the operator received the as-built drawings, test certificates for the electrical installation, a plumbing pressure test record, equipment warranties and a short maintenance guide: how often to change the water filter, how to clean the drains and grease traps, and who to call if a fridge stopped cooling. We also left a set of spare veneer panels and edge trims so minor damage from trolleys can be repaired quickly. A 12-month defects period covered workmanship, with a planned check after the first three months of trading.
Results
- The kiosk opened on the planned date and passed the landlord and authority inspections at the first visit.
- Two baristas can run the bar at peak times without leaving the footprint; stock is refilled at night from the corridor.
- Separate circuits removed the risk of afternoon breaker trips that the operator had experienced at a previous pop-up.
- The low menu panel kept the neighboring shopfronts visible, which the landlord highlighted as a reason to approve quickly.
Lessons learned
The biggest saving on a mall kiosk is off-site fabrication. Building the kiosk in modules in the workshop meant the night shifts were spent on assembly and connections rather than cutting and sanding in a live mall. The second lesson is to survey the space below before the design is fixed. On this project the drainage route had to dodge a sprinkler main, and finding that early avoided a redesign. Finally, heat planning is not optional: choosing fridges with front ventilation and splitting circuits costs little at design stage and saves a lot of trouble in July and August.
Key takeaways
- Kiosk services usually come from below the slab, so survey early and coordinate with mall facility management.
- Fabricate joinery off-site and design modules that fit the service lifts.
- Plan for heat from espresso machines and fridges from day one.
- Expect landlord, municipal, Civil Defence and food-safety steps; check current fees and timelines with each.
Planning a mall kiosk in Abu Dhabi or Dubai?
Indicative 2026 budgets for a kiosk of this size typically range from around AED 90,000 to AED 180,000 plus 5% VAT, depending on equipment, finishes and how services reach the unit; we confirm the price after a site survey. Talk to FIXORA Decor about your kiosk, café counter or pop-up: send your landlord criteria and floor plan on WhatsApp +971501962136, call +971 50 196 2136 or request a quote at /quote.


