Summer offer: 20% OFF AC deep cleaning — book before 30 JuneBook now
Skip to content

Fire-Rated Doors and Partitions in UAE Buildings Explained

Where fire-rated doors and partitions are required in UAE buildings, what FD30 and FD60 mean, how certification works and how to maintain door closers and seals.

Updated 13 Oct 20266 min read
Fire-Rated Doors and Partitions in UAE Buildings Explained
In this article

Quick answer

Where fire-rated doors and partitions are required in UAE buildings, what FD30 and FD60 mean, how certification works and how to maintain door closers and seals. A rating such as FD30 or FD60 means the complete doorset has been tested to hold back fire for 30 or 60 minutes.

Last updated:

Fire-rated doors and partitions are required in UAE buildings wherever a wall or door forms part of a fire compartment or protects an escape route: stair enclosures, corridors serving apartments and offices, apartment entrance doors in many towers, plant and electrical rooms, service shafts and certain kitchens and storage areas. A rating such as FD30 or FD60 means the complete doorset has been tested to hold back fire for 30 or 60 minutes. The UAE Fire and Life Safety Code of Practice sets the requirements, and Civil Defence inspects them during approvals. When you renovate, any rated element you touch must be replaced or repaired with an equivalent certified system. Requirements change — confirm with the authority or your community management before you start.

Why fire ratings matter

Fire compartmentation is what keeps a fire in one apartment or office from spreading through the building, and what keeps stairs and corridors usable for long enough for people to escape. A single non-rated door, an unsealed cable hole or a partition that stops at the ceiling instead of the slab can undermine the whole strategy. During renovations, these elements are often damaged or replaced without anyone noticing that they had a fire rating in the first place.

Where fire ratings are typically required

  • Stair enclosures and lobbies: doors and walls protecting escape stairs.
  • Apartment entrance doors: in many residential towers, the door between the apartment and the common corridor is fire-rated and self-closing.
  • Corridors: walls and doors along escape corridors in offices, hotels and residential buildings.
  • Plant, electrical and riser rooms: areas with higher fire risk or critical services.
  • Service shafts: access panels and doors to vertical shafts.
  • Commercial kitchens and storage: depending on use and layout.
  • Between different occupancies: for example, between a shop and a residential lobby.

The exact requirement depends on building height, use and the approved fire strategy. The fire and life safety drawings for the building or your fit-out, prepared by the consultant, are the reference.

What FD30 and FD60 mean

The FD rating describes how long a doorset maintains its integrity in a standard fire test, meaning it prevents flames and hot gases from passing through. Tests are carried out to recognized standards on the complete assembly, not just the door leaf.

RatingMeaningTypical usesTypical supply and install cost
FD3030 minutes integrityApartment entrance doors, corridor doors, many office doorsTypically AED 2,500–6,000 per single doorset
FD30S30 minutes integrity with smoke sealsDoors where smoke control is required, such as on escape routesTypically AED 2,800–6,500 per single doorset
FD6060 minutes integrityStair enclosures, plant rooms, some shafts and compartment wallsTypically AED 3,500–8,500 per single doorset
FD90 / FD12090 or 120 minutes integrityHigher-risk rooms and specific compartment requirementsPriced case by case

Costs are typical ranges, exclusive of 5% VAT, and vary with finish, size, glazing, ironmongery and quantity. Metal doors for plant rooms and timber doors with veneered or painted finishes for apartments are both common.

A doorset is a system

The rating belongs to the tested combination of components. Swapping any one of them for a non-tested item can void it.

  • Leaf and frame: tested together, with the correct core and frame profile.
  • Intumescent seals: strips that expand in heat to close the gap between leaf and frame.
  • Smoke seals: brush or blade seals for smoke-rated doors.
  • Hinges: the number, type and position used in the test, usually three or more per leaf.
  • Self-closing device: an overhead or concealed closer that reliably closes and latches the door.
  • Locks, latches and handles: fire-tested ironmongery, fitted with intumescent protection where required.
  • Glazing: fire-rated glass and beads where vision panels are included.
  • Gaps: perimeter gaps within the limits stated in the test evidence, typically just a few millimeters.

Certification and approval

In the UAE, fire-rated products used in buildings are expected to be backed by test reports from recognized laboratories, third-party certification and, where required, approval or listing by Civil Defence. A certified door usually carries a label or plug on the leaf edge identifying the manufacturer and rating. When buying doors for a renovation, ask for:

  • The test or assessment report covering the exact configuration.
  • Proof of certification and any Civil Defence approval or listing.
  • Installation instructions, and follow them exactly.
  • A record of the installed doors for your handover file, as described in completion certificates and handover documents.

Fire-rated partitions

Rated partitions, usually gypsum board systems on steel studs or blockwork, must be built exactly as tested: correct board type and number of layers, stud spacing, fixings and joint treatment. Critically, they must run from structural slab to structural slab, not stop at the false ceiling. Every opening for cables, pipes and ducts needs a certified fire-stopping product, and ducts crossing rated walls usually need fire dampers. These details are checked during Civil Defence inspections; see our guide to Dubai Civil Defence approval for fit-outs.

Maintenance: closers, seals and everyday habits

Fire doors only work when they are closed. Most failures found during inspections are maintenance issues rather than product issues:

  • Doors wedged or propped open with furniture or door stops.
  • Closers adjusted so the door no longer latches, or removed entirely.
  • Painted-over or damaged intumescent and smoke seals.
  • Gaps that have grown as hinges wear.
  • Non-rated replacement handles or locks.
  • Holes drilled for spy-holes, signs or extra locks without fire-rated products.

Building managers typically inspect common-area fire doors regularly. Apartment owners should check that their entrance door closes fully from any open position, that seals are intact and that hinges are tight. Where doors must be held open for convenience, approved hold-open devices linked to the fire alarm are the correct solution.

Common mistakes during renovations

  • Replacing an apartment entrance door with a decorative non-rated door.
  • Adding glass panels or letterboxes to rated doors.
  • Cutting rated partitions for new sockets or AC pipes without fire-stopping.
  • Painting over seals during redecoration.

Fire doors in apartments versus commercial spaces

In apartments, the most common fire door is the entrance door to the corridor. Owners often want to replace it during a renovation for a more modern look. That is possible, but the new doorset must match or exceed the original rating, usually include a self-closer and be approved by building management. A popular alternative is to keep the certified door and frame and change only the finish with a compatible veneer or paint system, together with tested ironmongery.

Commercial fit-outs involve more rated elements: corridor walls, doors to stairs, server and electrical rooms, and sometimes glazed fire-rated screens at reception areas. Glazed screens are attractive but are tested as complete systems, including frames, glass and sealants, and are considerably more expensive than plain partitions. Plan them into the budget early.

  • Keep a door schedule showing location, rating, manufacturer and certificate reference for every rated door.
  • Specify closers with adjustable closing and latching speeds so doors close reliably without slamming.
  • Where accessibility matters, choose closers with low opening force or use hold-open devices linked to the alarm.
  • Avoid floor finishes or thresholds that change the gap under the door beyond the tested limit.

How FIXORA Decor handles fire-rated elements

FIXORA Decor identifies rated doors and walls during the initial survey, specifies certified replacements, and keeps the certificates for handover. Our joinery team can match the appearance you want while keeping the rating intact.

Next step

If you need new or replacement fire-rated doors, or you are changing partitions in a fit-out, send us the door schedule or photos and we will prepare a free quotation. For door and frame work, see our joinery and carpentry service.

The information in this article is general guidance, not advice for your specific project. See our Terms.

Frequently asked questions

In many UAE towers it is. Check the edge of the door leaf for a certification label or plug, look for intumescent seals in the frame and a self-closer, and ask building management for confirmation. If it is rated, any replacement must have the same or a higher rating.
Yes, but only with ironmongery that is compatible with the door's test evidence and fire-tested itself. Fitting a standard lock or cutting a larger recess can compromise the rating. Ask your supplier for evidence that the hardware suits the specific doorset.
Both doorsets provide 30 minutes of fire integrity. The S indicates that the door also has smoke seals and has been tested to limit cold smoke leakage, which is important on escape routes where smoke spread is a key risk.
Common-area doors are typically checked by building management on a regular schedule, often every few months. Owners should check their own rated doors whenever they notice they no longer close fully, and after any work near the door. Closers and seals are the usual problems.

Sources

Was this article helpful?

Get new articles by email

Practical tips now and then. Confirm by email, unsubscribe any time.

Need help with your project?

Our team is ready to help — get a free quotation today.

Or call us+971 50 196 2136

Serving